XL-0895
SYNTHETIC POLYOLESTER-BASED OIL
XL-0895 series of synthetic lubricants are designed for the lubrication of bearings, chains,
slide-ways and gears where temperatures may exceed 150°C. These fluids are
anti-static, and will not leave any residue after the carrier evaporates. (Use XL-0895/900 series
for molybdenum residue)
XL-0895 is a polyolester-based lubricant formulated without any unstable polymers to
increase its viscosity index. This helps eliminate the formation of varnish and
carbon deposits at high temperatures. The inherent high viscosity index of XL-0895 permits
optimal lubrication across a wide range of temperatures.
XL-0895 does not leave any carrier residue, thereby eliminating the accumulation of solid
matter which may cause mechanical breakdowns and increase overall maintenance
costs. This fluid will, in most applications, dislodge existing sludge and
varnish formed from previous lubricant applications.
XL-0895 reduces energy consumption by maintaining a clean lubricating film, even at high
temperatures, which extends the interval between re-lubrication and reduces the
amount of oil consumed. This also reduces the smoke and odours inherent to hot
oil.
XL-0895 was formulated specifically to give maximum protection against wear, rust, oxidation
and corrosion, thereby prolonging equipment life, while reducing overall
maintenance costs.
ADVANTAGES:
• Exceptional stability at high temperatures
• Cleanliness
• Low Volatility
• Energy Efficiency
• Improved Protection
• High Viscosity Index
XL-0895 is
recommended for:
• High temperature conveyor chains.
• Chains for bottling plants.
• Chains in ceramic plants
• Bearings for drying ovens.
• Bearings, seals etc.
• Textile industry
| TYPICAL SPECIFICATIONS | ||||||||
|---|---|---|---|---|---|---|---|---|
| Product Code: XL-0895 | /046 | /068 | /100 | /220 | /225 | /229 | /320 | /460 |
| ISO Grade | 046 | 068 | 100 | 220 | 220 | 220 | 320 | 460 |
| SAE Grade | 10 | 20 | 30 | 50 | 50 | 50 | – | – |
| Viscosity (cst @ 40°C) (ASTM D-445) | 46.3 | 71.6 | 101 | 235 | 237 | 220 | 318 | 470 |
| Viscosity (cst @ 100°C) (ASTM D-445) | 7.5 | 10.8 | 12.9 | 24.0 | 25.4 | 18.8 | 29.1 | 40 |
| Viscosity Index | 127 | 140 | 124 | 128 | 130 | 95 | 125 | 125 |
| Rust Test (Distilled Water, 48 hrs) (ASTM D-6557) | Pass | Pass | Pass | Pass | Pass | Pass | Pass | Pass |
| Rust Test (Sea Water, 48 hrs) (ASTM D-6557) | Pass | Pass | Pass | Pass | Pass | Pass | Pass | Pass |
| Flash Point (°C) | 240 | 243 | 245 | 248 | 266 | 300 | 260 | 248 |
| Fire Point (°C) | 265 | 277 | 278 | 279 | 316 | – | 280 | 280 |
| Autoignition Point (°C) | 400 | 410 | 410 | 410 | – | – | 410 | 410 |
| Pour Point (°C) | <-40 | -40 | -38 | -37 | -18 | -36 | -32 | -22 |
| Residue (%weight) | <0.01 | <0.01 | <0.01 | <0.01 | <0.01 | <0.01 | <0.01 | <0.01 |
| Evaporation Loss 4hrs @ 204°C (% weight) | <2 | <2 | <2 | <2 | <2 | <0 | <1 | <1 |
| Shell 4 Ball Wear Test 40kg | 0.37 | 0.38 | 0.38 | 0.38 | 0.35 | 0.35 | 0.37 | 0.36 |
| Specific Gravity (g/ml @ 15°C) | 0.88 | 0.88 | 0.90 | 0.91 | 0.94 | 0.97 | 0.93 | 0.93 |
Before using one of
the XL-0895 series of fluids:
A special formulation containing a solvent (XL-0895/469)
should be used to clean the sludge left in equipment by previous oils.
Add XL-0895/469 at between 5 and 10% of the oil capacity and let the equipment run un-pressurized,
at a maximum temperature of 50°C for 24 to 48 hours.
Once completed, change the filter, drain the oil and replace it with new XL-0895 fluid
XL-0895
